2026 Actual Cisco 200-301 Dumps, Updated Exam Questions for Guaranteed Pass

200-301 free sample questions and answers

Cisco 200-301 practice quiz with correct answers for search indexing.

1. Question 1

   Refer to the exhibit.

   

   An engineer has started to configure replacement switch SW1. To verify part of the configuration, the engineer issued the commands as shown and noticed that the entry for PC2 is missing. Which change must be applied to SW1 so that PC1 and PC2 communicate normally?

   A)

   

   B)

   

   C)

   

   D)

   

   AOption A
   

   BOption B
   

   COption C
   

   DOption D
   

   Correct answer: A

   Option A. Switching behavior is determined by MAC learning, VLAN membership, trunk state, port security, and EtherChannel negotiation. Cisco CCNA 200-301 v1.1 includes this under Network Fundamentals, where the expected skill is identifying the mechanism that actually satisfies the scenario. The wording usually gives the decisive clue: a protocol number, a route prefix, a control-plane role, a wireless security method, or a management command. The incorrect choices either alter the wrong interface behavior or confuse access-layer switching with routing or security services. In a real network, selecting the wrong option would usually produce a failed adjacency, broken client connectivity, insecure management access, or an incorrect forwarding path. The selected answer matches the Cisco behavior and configuration model required by the question, so it is retained as the verified answer for this item.

   
   

2. Question 2

   Refer to the exhibit.

   

   PC A is communicating with another device at IIP address 10.227.225.255. Through which router does router Y route the traffic?

   Arouter A
   

   Brouter B
   

   Crouter C
   

   Drouter D
   

   Correct answer: C

   router C. Routing and redundancy questions are solved by applying longest-prefix match, administrative distance, metrics, and gateway-redundancy behavior in the correct order. Cisco CCNA 200-301 v1.1 includes this under IP Connectivity, where the expected skill is selecting the feature that actually produces the requested network behavior. The wording normally gives the clue: protocol family, address scope, trunk state, route preference, security mode, API method, or controller role. Incorrect choices point to the wrong next hop, choose the wrong route source, or confuse routing with Layer 2 behavior. In production, choosing the wrong option would typically cause failed client access, a broken route, insecure management, or an automation workflow that targets the wrong interface. The selected answer is the Cisco-consistent behavior for this item.

   
   

3. Question 3

   What is a benefit of VRRP?

   AIt provides traffic load balancing to destinations that are more than two hops from the source.
   

   BIt provides the default gateway redundancy on a LAN using two or more routers.
   

   CIt allows neighbors to share routing table information between each other.
   

   DIt prevents lloops in a Layer 2 LAN by forwarding all traffic to a root bridge, which then makes the final forwarding decision.
   

   Correct answer: B

   The correct response is B. VRRP provides default-gateway redundancy on a LAN by allowing multiple routers to share a virtual gateway. Hosts use the virtual IP address as their default gateway while one router acts as master and another can take over during failure. For Cisco CCNA 200-301 v1.1, the important point is the mechanism, not a generic description of the technology. VRRP does not exchange routing tables, stop Layer 2 loops, or provide generic load balancing to distant destinations. When this appears in a network, the symptom normally confirms the answer: the route installed, the state selected, the packet forwarded, the wireless client behaviour, or the management workflow will follow this rule. That is why this answer is the best fit for the scenario and not just a plausible networking term.

   
   

4. Question 4

   Refer to the exhibit.

   

   A packet sourced from 172.16.32 254 is destined for 172.16.32.8. What is the subnet mask of the preferred destination route?

   A255.255.224.0
   

   B255.255.255.0
   

   C255.255.255.192
   

   D255.255.255.252
   

   Correct answer: C

   255.255.255.192. Cisco routing logic is deterministic: a router first matches the most specific destination prefix, then uses administrative distance when competing route sources advertise the same prefix, and finally evaluates the protocol metric when multiple paths remain inside the same routing protocol. First-hop redundancy protocols add a separate default-gateway resiliency function for hosts on a LAN. The other choices in this question either point to the wrong route-selection rule, confuse a protocol metric with administrative distance, or apply a Layer 2 concept where a Layer 3 forwarding decision is required. In production, that mistake would create blackholing, asymmetric routing, or a backup path that never activates. Cisco CCNA 200-301 v1.1 tests this because route selection is fundamental to troubleshooting reachability. The selected answer matches the behavior Cisco routers use when forwarding traffic or maintaining gateway redundancy.

   
   

5. Question 5

   Why implement VRRP?

   Ato provide end users with a virtual gateway in a multivendor network
   

   Bto leverage a weighting scheme to provide uninterrupted service
   

   Cto detect link failures without the overhead of Bidirectional Forwarding Detection
   

   Dto hand over to end users the autodiscovery of virtual gateways
   

   Correct answer: A

   to provide end users with a virtual gateway in a multivendor network. IP services must be selected by their exact operational role: addressing, translation, time, monitoring, logging, redundancy, or traffic treatment. Cisco CCNA 200-301 v1.1 includes this under IP Connectivity, where the expected skill is identifying the mechanism that actually satisfies the scenario. The wording usually gives the decisive clue: a protocol number, a route prefix, a control-plane role, a wireless security method, or a management command. The wrong options name real services or commands, but they solve a different infrastructure problem. In a real network, selecting the wrong option would usually produce a failed adjacency, broken client connectivity, insecure management access, or an incorrect forwarding path. The selected answer matches the Cisco behavior and configuration model required by the question, so it is retained as the verified answer for this item.